Home›Success stories›Flow monitored channel by channel in an 8-cavity mould
Injection moulding

Per-channel flow monitoring in an 8-cavity multi-cavity mould

In an 8-cavity mould, each cooling channel behaved differently and nobody could see it. A MARSE electronic multi-circuit distribution unit mounted on the mould measures flow, temperature and pressure in each channel and turns cooling into continuous quality control.

SectorPlastic injection
Mould
8 cavitiesmulti-cavity
Equipment
Multi-circuit distributionelectronic, on the mould
Measurement
Flow, T and Pin each channel
Quality
Per-channel controlalarms and logging
Molde multicavidad antes y después de instalar la distribución multicircuito electrónica MARSE
Before and after: from uneven hoses to a multi-circuit distribution unit mounted on the mould.

The case at a glance

Mould
Multi-cavity, 8 cavities.
Equipment
MARSE electronic multi-circuit distribution, mounted on the mould.
Measurement
Flow, temperature and pressure of each channel.
Aim
Channel-by-channel quality control and fewer rejects.
Integration
Synchronised with the MARSE temperature control unit.

The process and the initial problem

In a multi-cavity mould, all cavities should cool the same. In practice, with a passive manifold each channel receives the flow its hose allows: different lengths, elbows, limescale or dirt change the pressure drop of each circuit.

For the process engineer, the problem is that heat extraction depends on turbulent flow: a channel with low flow cools less well, that cavity comes out hotter and the part varies in dimensions or warps. And the cycle of the whole mould is set by the slowest cavity. Without measuring each channel, all this is only discovered through rejected parts.

Before and after

Before, there was no data on any channel. Now every channel is visible, logged and raises an alarm if it goes out of range.

Before
  • Hoses of different lengths
  • Passive manifold, with no information on the distribution
  • A problem channel was only discovered through the parts
After
  • Distribution unit mounted directly on the mould
  • Short, equal hoses: supply in red, return in blue
  • Flow, temperature and pressure of each channel on screen

Why MARSE multi-circuit distribution in this case

For the process engineer

  • Flow, temperature and pressure of each channel in view: you know which cavity is working out of range.
  • Thorough quality control: every cavity is monitored in every cycle.
  • Recipes per mould: the same values at every start-up.
  • Data logging to relate cooling to part quality.

For the maintenance manager

  • A blockage caused by limescale or dirt triggers an alarm on its channel before it affects production.
  • Mounted on the mould, with short, equal hoses: lower losses and a tidy installation.
  • 7″ touch screen: diagnostics without dismantling anything.
  • Modular format with 2 to 12 zones per unit.

Technical keys

  1. Measure every channelFlow, temperature and pressure of the mould circuits, in real time.
  2. Detect it before the part doesThe fault shows up on the screen before it reaches quality control.
  3. Stable cycleNo slow cavity sets the time for the whole mould.
  4. TraceabilityLogged data and recipes per mould.

Result

Per-channel controlEvery cavity, monitored at all times.
Fewer rejectsProblems are seen before they reach the part.
Data for decision-makingLogging of every channel and recipes per mould.

Frequently asked questions

Why is a passive manifold not enough in a multi-cavity mould?

Because it distributes flow according to the resistance of each hose, not according to what each cavity needs, and it gives no information: a channel with low flow is only detected when bad parts appear.

What does the electronic multi-circuit distribution unit measure?

Flow, temperature and pressure of each circuit, with alarms, data logging and recipes per mould.

How does it reduce rejects?

By detecting in the channel, in real time, any loss of flow or temperature deviation before it affects the part.

Equipment and technology

Other success stories

← All success stories
Do you have a similar process?Tell us what you need to solve and we will propose the right unit.
Talk to a specialist

Per-channel flow monitoring in an 8-cavity multi-cavity mould

Equipment with marking EC · European conformity
MARSE
Privacy Summary

This website uses cookies to offer you the best possible user experience. Cookie information is stored in your browser and performs functions such as recognizing you when you return to the website and helping the computer understand which sections of the website you find most interesting and useful.