Home›Success stories

Success stories

Real installations of our temperature control units, thermoregulators and flow control systems. For each case we explain what the customer needed, which equipment we installed and the technical data it works with.

Four SMART W TS integrated into an extruder
Extrusion

Four SMART W TS integrated into an extruder

Four 90 °C water SMART W TS units mounted on the base frame of an extruder of about 70 kg/h.

Sector
Plastics · polyolefin production
Units
4 × SMART W TS
Extruder
≈ 70 kg/h
View case →
Four temperature control units without display, controlled from the line
Flexographic printing and lamination

Four temperature control units without display, controlled from the line

No display: the lamination line sends the setpoints and receives the status of each unit.

Sector
Packaging · flexographic printing and lamination
Units
4 temperature control units
Connection
24-pin connector
View case →
Cleanroom reactors without exceeding their maximum pressure
Chemicals · Aerospace

Cleanroom reactors without exceeding their maximum pressure

Always below the reactor's maximum pressure, with fine control of temperature and cycle times.

Sector
Chemicals and aerospace
Fluid
Oil (water in some cases)
Pressure
Below the reactor max.
View case →
9 mould circuits controlled with MARSE Flow Basic
Injection moulding

9 mould circuits controlled with MARSE Flow Basic

Nine circuits monitored one by one: per-channel quality control instead of distributing flow blindly.

Sector
Plastic injection
Equipment
MARSE Flow Basic
Circuits
9
View case →
Preheating several moulds at once with a 72 kW SMART 6
Injection moulding

Preheating several moulds at once with a 72 kW SMART 6

A 72 kW SMART 6 heats several moulds at the same time, before the mould change comes round.

Sector
Plastic injection
Equipment
SMART 6 · 72 kW
Molds
Several at once
View case →
Grinding a drum over 2 m long, already expanded
Metal

Grinding a drum over 2 m long, already expanded

A drum over 2 m long is ground at its working temperature, with the material already expanded.

Sector
Machine building · metal
Drum
Ø and length > 2 m
Thermal expansion
≈ 12 µm/m·°C
View case →
300 °C oil temperature control unit instead of a boiler
Special project

300 °C oil temperature control unit instead of a boiler

A 300 °C oil SMART 6 PLUS replaces a boiler: from 700 to about 100 litres of oil in the whole installation.

Sector
Chemicals · hot melt production
Equipment
SMART 6 PLUS · 72 kW
Oil
700 l → ≈ 100 l
View case →
Jacketed reactors of up to 2,000 l with 3 bar jackets
Chemistry and pharmacy

Jacketed reactors of up to 2,000 l with 3 bar jackets

Jackets of up to 3 bar and reactors from laboratory to production scale of more than 2,000 litres.

Sector
Chemicals · hot melt production
Jacket
Max. ≈ 3 bar
Reactors
Up to > 2,000 l
View case →
SMART 10: two independent circuits with the same setpoint
Special project

SMART 10: two independent circuits with the same setpoint

Twin pump, all in stainless steel and leak-free press-fit joints for the chemical industry.

Sector
Chemical
Equipment
MARSE SMART 10
Circuits
2 · same setpoint
View case →
Flow monitored channel by channel in an 8-cavity mould
Injection moulding

Flow monitored channel by channel in an 8-cavity mould

Every circuit of an 8-cavity mould, measured and monitored: channel-by-channel quality control.

Sector
Plastic injection
Cavities
8
Control
Per channel
View case →
A standardised injection moulding plant with more than 100 temperature control units
Customer loyalty

A standardised injection moulding plant with more than 100 temperature control units

More than 15 years with the same customer: more than 100 direct-cooling and tank temperature control units, recently renewed.

Sector
Automotive · plastic injection moulding
Units
100+ temperature control units
Relationship
More than 15 years
View case →
A 1997 MARSE MTR-36 comes back to the factory
Customer loyalty

A 1997 MARSE MTR-36 comes back to the factory

A customer brings us their 1997 MARSE MTR-36 to keep it as a memento.

Sector
Automotive · plastic injection moulding
Model
MTR-36
Built
18-9-1997
View case →
Do you have a similar process?Tell us about your application and we will propose the right unit.
Talk to a specialist

Success stories

Equipment with marking EC · European conformity
MARSE
Privacy Summary

This website uses cookies to offer you the best possible user experience. Cookie information is stored in your browser and performs functions such as recognizing you when you return to the website and helping the computer understand which sections of the website you find most interesting and useful.