Home›Success stories›SMART 10: two independent circuits with the same setpoint
Special project

SMART 10: double-circuit, twin-pump temperature control unit for the chemical industry

A chemical industry customer needed a high flow rate in two independent circuits working at the same temperature. MARSE designed the SMART 10: a unit with two pumps, two separate hydraulic circuits under a single setpoint, pressure control with an expansion vessel and a large heat exchanger to cool both circuits.

SectorChemical
Equipment
SMART 10special project
Circuits
2 independentone pump per circuit
Setpoint
Singlefor both circuits
Refrigeration
Large heat exchangerfor both circuits
Interior of the MARSE SMART 10 double circuit temperature control unit: two pumps, expansion vessel and plate heat exchanger
SMART 10 in the factory: two pumps, expansion vessel and high-capacity plate heat exchanger.

The case at a glance

Equipment
MARSE SMART 10, double-circuit special project.
Construction
All in stainless steel, with components specified by the customer.
Circuits
Two independent circuits, each with its own pump.
Setpoint
The same working temperature for both circuits.
Pressure
Controlled, with expansion vessel.
Refrigeration
Large heat exchanger for both circuits.
Joints
Inoxpres press-fit on all connections: no leaks.

The process and the initial problem

The customer had two consumers that had to work at exactly the same temperature, but with a high flow rate in each one and without one circuit affecting the other. With a single circuit split between the two, the flow rate is divided according to the pressure drop of each branch, and a change on one side is felt on the other.

The solution was to separate the hydraulics and unify the control: two circuits, each with its own pump, governed by a single setpoint. In addition, the process generates heat, so the unit needed a large cooling capacity in both circuits and pressure control to work stably at temperature.

As this is the chemical industry, the entire circuit was built in stainless steel, with the components specified by the customer, proportional valves for regulation and Inoxpres press-fit joints on all connections: each joint is mechanically fixed and sealed, with no risk of it coming loose and no fluid leaks.

Challenge and solution

Separate the hydraulics and unify the control.

The challenge
  • Two consumers at the same temperature
  • High flow rate in each one
  • One circuit must not affect the other
The solution
  • Two independent circuits, one pump per circuit
  • All in stainless steel, with leak-free press-fit joints
  • Expansion vessel, proportional valves and large heat exchanger

Why a MARSE temperature control unit in this case

For the process engineer

  • Two hydraulically independent circuits: each receives its own flow rate, with no splitting between branches.
  • A single setpoint for both circuits: the same temperature at both consumers.
  • Large heat exchanger: capacity to remove the process heat from both circuits.
  • Pressure control with expansion vessel: the system absorbs the expansion of the fluid as it heats up.
  • Proportional valves for fine regulation of each circuit.

For the maintenance manager

  • One pump per circuit: an incident in one circuit does not affect the other.
  • A single unit instead of two temperature control units: less space, less wiring and a single control point.
  • All in stainless steel: corrosion-resistant in a chemical environment.
  • Inoxpres press-fit joints: they do not loosen with vibration or thermal cycling, and prevent fluid leaks.
  • Components chosen by the customer: the same ones its maintenance team already uses.
  • Designed, manufactured and supported by MARSE.

Technical keys

  1. Twin pump, double circuitEach circuit with its own pump and flow rate.
  2. A single setpointBoth circuits at the same temperature.
  3. Pressure under controlExpansion vessel to absorb the expansion of the fluid.
  4. High cooling capacityHeat exchanger sized for both circuits.
  5. Stainless and leak-freeAll in stainless steel, with Inoxpres press-fit joints.

Result

Flow rate on both sidesNo splitting or interference between circuits.
Same temperatureA common setpoint for both consumers.
A single unitCustom design instead of two temperature control units.

Frequently asked questions

What is the MARSE SMART 10?

It is a special-project temperature control unit with two independent hydraulic circuits, each with its own pump, working under a single temperature setpoint.

Why two circuits instead of one split circuit?

Because this way each consumer receives all the flow rate it needs and a change in one circuit does not affect the other, keeping the same temperature in both.

What is the expansion vessel for?

To absorb the expansion of the fluid as it heats up and keep the circuit pressure under control.

How are leaks prevented?

The entire circuit is made of stainless steel and all joints are press-fitted with the Inoxpres system: each joint is fixed and sealed, with no risk of it coming loose.

Why such a large heat exchanger?

Because the process generates heat and the unit has to be able to remove it from both circuits at the same time.

Equipment and technology

Other success stories

← All success stories
Do you have a similar process?Tell us what you need to solve and we will propose the right unit.
Talk to a specialist

SMART 10: double-circuit, twin-pump temperature control unit for the chemical industry

Equipment with marking EC · European conformity
MARSE
Privacy Summary

This website uses cookies to offer you the best possible user experience. Cookie information is stored in your browser and performs functions such as recognizing you when you return to the website and helping the computer understand which sections of the website you find most interesting and useful.